Hello... I can't figure out what I'm doing wrong, or if there's something wrong with my Thor 4... Basically the problem I'm having is, I can't see the lazer dot when trying to zero my ABL. I tried day, or night, 50+yds, 10 ft, pointing at something hot, and no matter what, I can't see the lazer dot through the scope. Any help would be great... Probably something stupid and simple, I'm not smart enough to figure out... Thanks.
Having that same issue. I go to "Zeroing ABL" I point the laser at a hot target, but when I look through the scope I DO NOT SEE THE laser dot. I move the red reticles where the dot on the target is and try to center it as close as I can by looking at the target and then back at the reticles through the scope. then I press "OK" and exit out of the settings menu. when I push the button on the scope to activate the ABL laser to take a range reading, the red reticles are off to the upper left/top (10 o'clock) and not centered with the scope's reticles. Its quite annoying because the ABL reticles are not aligned with the scope reticles. I am using the ABL1500 with the ATN THOR 4 (4x40). Any suggestions on how to align the ABL reticles to be centered with the scope reticles would be greatly appreciated.
Post by madmadhoosier on Nov 19, 2020 1:52:32 GMT -8
Same issue as you guys. If the red laser dot is not visible through the scope, how can the manual not mention that?
After several trials, I finally clamped my gun on a tripod and stabilized the laser dot on the center of a thermal target at the recommended 50 yard distance. Then carefully adjusted the brackets of the scope around the center of the thermal target.
It seems to me if I could do this again from a longer distance, say 75 or 100 yards the alignment would be even more precise for longer distance ranging. I will experiment with that another time, but hope the above helps.
X-Sight HD II 5x20x (5/11/16) Thor 4 40 (11-12-20)
What I did was make a target with a point on it that can be seen through the scope. Set the middle of the target up in the center of the scope. Then adjust your abl laser to the center of the target and you’re good.
alarmtech82: hello are the screens on the lt 3x6 supposed to flash out when you fire?
Jun 21, 2021 8:25:44 GMT -8
frogers64: Tried to download update for 4x 5-20 could not any help
Jun 22, 2021 11:36:54 GMT -8
rozidin: Please help me my scope Xsight2 firmware fix
Jun 23, 2021 13:38:40 GMT -8
swsnbw: Hi All. 4K mounted on a nice rifle used mainly for varmint control. Coyotes and raccoons, which tend to over-run us. Have enjoyed the ATN mostly -- sometimes it's a bit finicky about shutting down.
Jul 2, 2021 11:21:08 GMT -8
dough: Hi this is dough, I am new to the the forum and thermal tech. One question, I have the Binox 4T and find that the power button is accidentally turned on when putting the scope in a case or cover and then pulling the scope out a day later to find no power
Jul 19, 2021 13:08:05 GMT -8
standard6: Anyone out there have a source for a head harness that will work with a PS31 ? The manual says that it is optional, but even a call to ATN directly produced nothing. What I was told is that the head harness is something ATN is thinking of producing.
Jul 23, 2021 11:08:09 GMT -8
markmissalot: Hi, between myself and my sons we have 3 X sight 4K scope and have just after a lot of trouble just updated them to the latest software. THANK YOU TO SOPHIE FROM ATN EUROPE FOR THE HELP! However now all 3 scopes have the SMF warning on them can anyone help
Aug 3, 2021 14:02:05 GMT -8
daisia6449: Hello, are you guys ready to make real cash? No dull moments anymore. No more depending on cheap checks every week. Get thousands of dollars or any currency of your choice and make this life worth living for. Order for a blank ATM card now. How does it wo
Aug 8, 2021 5:42:42 GMT -8
kuro0531: Hello from Southern Oregon. New to the sight and searching for some answers on my ATN 4K PRO.
Aug 8, 2021 20:42:53 GMT -8
blackbear: I thought everyone was crazy when they were saying to spin the scope this way then another way and another, ( Like the old joke of swinging a chicken over your head ) Well I’m convinced, The figure 8 then the merry , ring around, then the tire A Big THANKS
Aug 12, 2021 6:51:47 GMT -8
johann: aNYONE HER USING LASER IR INSTEAD OF TE CONVENTIONAL IR
Aug 15, 2021 13:34:05 GMT -8
johann: aNYONE USING LASER IR INSTEAD OF CONVENTIONAL IR
Aug 15, 2021 13:34:55 GMT -8
pcduenas: Hi, I am having problems with my one shot zero. The zero reticle seems to be maxed out. It won't go down any further. I tried restoring factory settings as well as doing a firmware update. Still does not work. Please help???
Aug 25, 2021 18:00:06 GMT -8
swiggs: I had the same issue. I have a 3" height difference middle of barrel & Scope . I ordered adjustable scope rings (Burriss) which allowed me to create a "-25 MOA" (front ring lower than back) which moved the reticle back to the middle and all is ok!
Aug 26, 2021 6:02:52 GMT -8
wadriano: Greetings from Brazil
Sept 2, 2021 12:05:51 GMT -8
solengo19: Ho un Visore notturno -diurno ATN 4 k 5x20,in piu occasioni mi si e' bloccato,dopo aver premuto il tasto accensione e tasto posteriore del visore sono riuscito a spegnerlo. L'azzeramento del cannocchiale si perde dopo questo ripristino?A me sembra di si.
Sept 12, 2021 1:02:07 GMT -8
grifton01: Using ABL with x-sight 4k pro 3-14. I have 2 questions. After zeroing the ABL with scope at 42 mtrs i have the following questions. Q1. when using the rage finder button on the scope, the ABL put up a box that is not in line with my retical point of aim.
Sept 17, 2021 23:37:21 GMT -8
grifton01: ABL retical Q2. After ABL works out distance my point of aim retical moves up the longer the distance. This means I have to aim lower to put retical on target. I would expect it to move down so that I aim higher.
Sept 17, 2021 23:46:16 GMT -8