Follow these steps: Insert an SD card into the scope Format the SD card in the scope Turn off scope Take out SD card and insert into computer Copy the firmware onto the SD card, into the root folder (not the ATN folder created by the scope) Insert SD card into scope and turn it on This will prompt the firmware update. Click yes and wait for completion After you have updated the scope make sure you do a factory reset and then choose the correct Device/Lens Type.
If you have sighted in your scope then make sure you export your profiles and write down your X & Y.
Post by luigiluigi1025 on Dec 6, 2018 13:10:43 GMT -8
You have to push the power button for 20 seconds. This will (should) switch off. I don’t find any utility in resetting. It runs as before. In any case, is e never ending story: in my case, after updating, the reticle is out of the center of display 😡
Post by Panic Button on Dec 14, 2018 16:39:07 GMT -8
Here's what works for the xs2, maybe the same will work with the 4k.
If you are trying to install the same version number or lower and you have not changed the file name, it will not display an update window during power up. The file has to be a new version than what's loaded in the scope.
The way to get around that is to rename the file using a higher version number for the file name. Also, if the file is renamed to xsight2.bin it will load it during power up and display update window no matter what version it is.
I've done this many times with my xs2 and it's always worked.
I don't know if using the same xsight2.bin rename will work with the 4k, but you can try it. Maybe the 4k uses a different name? If so, maybe some can chime in and clue us in. I'd like to know, I just received my new 4k yesterday.
FX Crown, .22 cal, synthetic stock ATN X Sight 4k Pro 3x14 Benjamin Marauder, Gen-2, Synrod, .22cal ATN X Sight II HD 3x14 80 cu ft scuba tank w/gauged fill hose Yong Heng 4,500psi compressor
guyton: how do i send out a message for help to all users?
Feb 10, 2022 13:02:04 GMT -8
guyton: I need advice on how to post to all users when I have a question
Feb 10, 2022 13:08:23 GMT -8
timspeed: I have a IR850 that doesn’t work. I have a charged 18650 battery and multimeter. The neck shows continuity from the pos terminal spring to the red wire on the face of the Cree board. The neg black wire on the Cree board shows no continuity to the housing.
Mar 9, 2022 20:26:14 GMT -8
timspeed: Is this board dead? Does anyone check in from atn to get us help?
Mar 10, 2022 8:32:38 GMT -8
smiles2da: Good morning, smiles2da here, I have the 4k pro 5-20
Apr 3, 2022 9:32:09 GMT -8
kriket2: Newbie w 4K pro. Was playing in range finding and trying to get to carousel when ‘target is unreachable’ pops up AND Now nothing works except shutdown. How do I get back to anything? Help!
May 4, 2022 17:26:55 GMT -8
opc: Good day, found website inside cover of box, new too 4k pro 5-20.
May 16, 2022 12:38:02 GMT -8
adrie: Dear ATN Form members. What is going on? I have a ATN X-sight 4k pro 3-14 scope. I sighted in at 20m. at 23m pellet hits 6mm to the right, 17m 2 mm to the left, at 11 m5 mm to the left and at 6m 6mm to the left. No wind. Please help! Gun, FX Impact M3 .22
May 21, 2022 5:51:14 GMT -8
bollingerc2: presti , instructions specifically say you have to re-calibrate compass after updating firmware. so pull scope off gun and do your re-calibration procedure
Jun 10, 2022 5:15:56 GMT -8
bollingerc2: adrie i'd verify the scope is tight and properly mounted. if you've had a different scope on it and you know its not the rifle barrel i'd think you need to check the scope mounts first, then check that the digital zero is saving .
Jun 10, 2022 5:27:18 GMT -8
krissy: Can anyone help? When using my ATN PS15-WPT goggles, I can see that the IR850-B1 does not stop glowing. I rotate the switch on the base to "OFF", but the IR lamp still glows.
Jun 13, 2022 15:47:52 GMT -8
ranger: Hi thx for the add- I have an 4k Pro with ABL 1000- Everything is paired,zeroed, and bullet info entered in Ballistcs calculater- my 5.56 zeroed at 100 yds is 3 inches low at 200 yds ? I don't know why and am very frustrated because I need 600 yd shots --
Jun 23, 2022 15:28:36 GMT -8
ranger: Im shooting a Hornady 75gr BTHP , is it possible this bullet is not in data bank ?
Jun 23, 2022 15:50:32 GMT -8
iandean: Hi Guys, complete newb. Can anyone tell me if I can tell what version of the X Sight 11 HD I have. I bought it second hand and can't seem to tell whether its a 3x14 or 5x20? Any help would be appreciated.
Jun 24, 2022 5:48:39 GMT -8
beast: jtrottany: The IR does not project a visible beam but do not believe for a sacond that some animals cannot see it. I've had numerous pigs immediately look directly at me as soon as I light them up.
Jul 18, 2022 4:18:42 GMT -8
bmyers: New here. I have a 4K 5-20 that i am trying to learn. Having a hard time in Night mode. it is basically just fuzz. Where should I start with learning and figuring out?
Jul 21, 2022 6:41:47 GMT -8
b308: ranger: you are low at 200 because BC for your bullet might be incorrect (find it on Hornady website) or your muzzle velocity is lower than you think. Chronograph it, every rifle is different and moderators etc affect it, so manufacturer data is approx.
Jul 26, 2022 6:54:30 GMT -8
beast: bmyers: Are you using the IR light that came with the scope?
Jul 29, 2022 3:41:59 GMT -8
cwentworth: Trying to update firmware on Thor LT Not seeing anything on scope
Jul 30, 2022 19:52:19 GMT -8
matth3w: TRYING TO RESET MY THOR LT IT HAS A BLANK SCREE
Jul 31, 2022 15:55:48 GMT -8